-
Who this checklist is for (and who can skip it)
-
The 7-point check
-
1. Read the spec sheet against the single-line diagram — not the other way around
-
2. Demand the usable capacity number, not the nameplate number
-
3. Derate the panel's wattage for real roof temperature (the one most people skip)
-
4. Separate continuous output from surge, every time
-
5. Confirm the monitoring app — and who owns the data
-
6. Price the total cost, not the line item
-
7. Turn the warranty from a slogan into a document
-
1. Read the spec sheet against the single-line diagram — not the other way around
-
Common traps I still see
-
Before you close this tab
I'm a quality and brand compliance manager at a renewable energy systems integrator. Every equipment spec sheet and customer quote that goes out has to pass through me first — roughly 40 a month. In 2024, I rejected 31% of first deliveries. Maybe 28% — you'd have to split hairs between actual defects and paperwork misfires.
That's expensive. It's also slow. But it's cheaper than finding out on the roof.
What follows is the 7-point check I run before signing off on any inverter, battery, or PV module. It's built for C&I and small commercial rooftop projects, but items 2, 3, and 4 apply to anything with a plug on it. Each check takes 5 to 15 minutes.
Who this checklist is for (and who can skip it)
If you're a facilities manager, an installer's procurement lead, or an energy service provider reviewing a spec package — this is for you. If you're standing in a garage picking out a 300W inverter for a weekend camper build, you only need steps 4 and 6. Skip the rest.
Three things make this worth the time:
- The kWh on a battery label isn't the kWh you can use.
- A panel's wattage gets measured in a lab, not on a 45°C rooftop.
- Dealer prices usually exclude commissioning, monitoring, and the first spare part.
The 7-point check
1. Read the spec sheet against the single-line diagram — not the other way around
Ask for the SLD first, then check the spec against it. Most mismatches show up here: the inverter's AC output is rated at 10 kW but the panelboard downstream only takes 8 kW, or the battery module's charge rate is higher than the inverter's max charge current.
We had a batch land in 2022 where the inverter said "10 kW" in the marketing sheet. That was peak at 25°C. Continuous output was 8 kW. We ran one for 48 hours at rated load and it derated hard. The vendor said it was "within industry standard." The derating curve was on page 43 of the service manual, not the sales sheet. We sent the batch back, and they redid it at their cost. Now every contract we write includes a continuous-output line item.
2. Demand the usable capacity number, not the nameplate number
A 5 kWh battery module doesn't hand you 5 kWh. Depth of discharge, temperature, and cycle degradation eat into that. For the Huawei Luna2000 5 kWh module, plan on something closer to 4.5 kWh of usable energy under reasonable conditions — confirm that against the warranty document the vendor provides, not against the brochure.
Same story at small scale. If you're looking at an EcoFlow Delta 1300 solar generator, the nameplate reads 1,260 Wh. The usable number is different. No one's trying to hide it — it's just that no one reads the tables at the back of the manual either.
3. Derate the panel's wattage for real roof temperature (the one most people skip)
A flexible solar panel rated 200W gets measured under Standard Test Conditions — 1,000 W/m² irradiance, 25°C cell temperature. On a black commercial roof in summer, a flexible panel's cell temperature hits 70°C and higher. Standard power temperature coefficients run about −0.3% to −0.45% per degree above 25°C. On a 45°C rise, a 200W flexible panel is realistically a 155–160W panel.
Flexible panels shed heat worse than glass-backsheet modules because there's no air gap behind them. So don't compare a flexible solar panel 200W home install directly against a 200W glass panel. If you're sizing a system against what a 300 watt power inverter can carry, use the derated number. Use the sunny-day number and you'll be 20% short on every load calculation you make.
4. Separate continuous output from surge, every time
Here's what a 300 watt power inverter will actually run: a laptop charger (60–90W), a router, LED lighting, a box fan, a 32–43" TV (100–150W), phone chargers. That's roughly the ceiling.
What it will not run: a microwave, an electric kettle, a space heater, or a full-size fridge — a fridge compressor pulls 900–1,200W at start-up sometimes for just a second or two.
Inverter spec sheets almost always list both continuous and peak. Peak is usually only good for a few seconds, and budget inverters often quietly cut that number. If the label only says "300W" with no qualifier, assume it's the peak figure and go find the real continuous rating. Ask in writing.
5. Confirm the monitoring app — and who owns the data
Huawei's monitoring runs through the FusionSolar app and cloud portal. Before you sign anything, get three questions answered in writing:
- Does the site buffer data locally when the internet drops, or does it just vanish?
- Is there a documented API, and does it survive a five-year horizon? (This matters if you're feeding a BMS.)
- If the client changes vendors later, who owns that data?
I got burned on this one. In 2022 we installed a system that only reported to the manufacturer's cloud, with no local option. The client later wanted to tie it into their building management system. We ended up boxed in behind an API licensing fee. Now every monitoring package we specify has to include either Modbus on-site or a written API access clause. Written into the contract — not promised in an email.
6. Price the total cost, not the line item
This is where most projects lose money. The battery module price is one line. Then comes wiring, commissioning, back-up panel tie-in, the first spare part, and expedited freight if the deadline slips.
On the Huawei Luna2000 battery price: as of January 2025, dealer listings for the 5 kWh module ranged roughly $2,100 to $3,400 depending on market, excluding installation and the backup box. That's a moving number — verify it against current quotes before you plan a budget around it.
I learned the freight lesson the hard way. In 2023 we chose standard ground shipping to save about $90 on a battery module. Delivery ran nine days past the install window. We rented a temporary backup unit for the building — $1,200. Saved $90 to spend $1,200, and the client noticed. We don't shave freight on large equipment anymore.
7. Turn the warranty from a slogan into a document
"10-year warranty" means nothing until you've read the actual warranty PDF. Find the response section. How fast do they respond after the ticket opens? 48-hour response or 48-hour repair? And who pays shipping when a unit fails in year four?
Cycle count matters too. Huawei's Luna2000 data sheet states 6,000 cycles and 10 years — verify that against the data sheet yourself rather than a distributor's summary. For consumer-grade units like the EcoFlow Delta 1300 solar generator, the warranty terms are commonly in a 24-month range, but the exact figure depends on where you buy and which market you're in. Channel and country terms matter here.
Common traps I still see
- A kW and a kWh get mixed up on a quote, usually by a new sales rep. We had a spec with "10 kW battery" in 2021 that turned out to be a 10 kWh unit. It took two weeks to untangle, and the client was already asking questions.
- One quote, no cross-check. In Q3 2024 we sent identical specs to four suppliers and saw a 38% spread between the lowest and highest. A single quote is a guess, not a price.
- Skipping the site walk. Roof loading in kg per square meter, orientation, shading — each one can invalidate your sizing before you've picked a single component.
- Mixing consumer-grade and commercial-grade hardware in one proposal. An EcoFlow Delta 1300 works fine as a small backup unit. It isn't commercial UPS equipment, and it shouldn't be presented as such.
Before you close this tab
One caveat, because this matters: none of this checklist is meant for a home 10 kW install. If you're putting a flexible solar panel 200W home setup on a shed with a 300 watt power inverter underneath it, relax step 5. Don't skip steps 2, 3, or 4, though. Those are the ones that actually bite.
And nothing on this list is clever. It's slow, repetitive, and annoying for whoever has to gather the paperwork. But when we skipped step 1 on a commercial job in 2022, site rework cost us $22,000 and delayed handover by three weeks. I'll take the paperwork every time.
Prices and reference data in this article are timestamped January 2025. Verify current rates and product specifications against the manufacturer's live documentation before placing any order.